Undersink Water Filter Kit, Lead, Chlorine & Cyst Reduction

PENTAIR SKU: UBSTD-KIT-CBR2-10

$149.00 $229.00 Save $80

Tax includedShipping calculated at checkout

Available Now!

Application

Drinking water System

Undersink - connects to cold water 

Provides - enhanced filtration capabilities, including reducing lead, cysts, certain chemicals, chlorine taste, and odor. The 0.5 micron rating means its capable of reducing 99.95% of Cryptosporidium, Toxoplasma, Entamoeba and Giardia Cysts.

This 10" Heavy Duty Standard size housing is perfect for mains pressure water filtration. It is Ideal to filter all cold water to your kitchen faucet without needing an extra tap on the benchtop and ensures minimal pressure drop. 

Recommended for Chlorinated or Rural water supply

Includes

  • 15mm BSP fittings for easy connection.
  • 10" Standard size housing, mounting bracket, and stainless steel fixing screws
  • 15mm x 600mm flexi pipe
  • Housing spanner
  • 1 x Pentair CBR-2-10

We recommend installing a pressure limiting valve before the housing for optimal performance and to prevent water hammer damage.

Specifications

This filter element tested and certified under ANSI/NSF Standard 42 & 53 for materials only

  • Filter Media – Coconut shell carbon
  • Temperature Rating – 40-125°F (4.4-51.7°C)
  • Maximum Pressure125 psi
  • Size 2.88" x 9.75" (73 mm x 248 mm)
  • Chlorine taste & odor reduction at flow rate -  18,900L @ 3.8 Lpm
  • Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Activated carbon block filters are not designed to remove bacteria or viruses.

Installation

Step 1: Shut Off Water Supply

  • Turn off the water supply to the dishwasher by shutting off the cold-water feed under the sink.

Step 2: Disconnect Dishwasher Water Feed Line

  • Locate the cold-water feed line under the sink that supplies the dishwasher.
  • Use an adjustable wrench to disconnect the 1/2" flexi hose that runs from the water supply to the dishwasher.

Step 3: Fit the brass 1/2" male threads

locate the brass threaded fitting supplied with the filter to the inlet and outlet of the filter using thread tape. 

Step 4: Connect 1/2" Flexi Hose to Filter Inlet

  • Take one of the new 1/2" stainless steel flexi hoses and wrap the threads with Teflon tape to ensure a tight seal.
  • Attach one end of the new hose to the water supply connection (where the dishwasher was previously connected).
  • Connect the other end of this hose to the inlet of your underbench water filter system.

Step 4: Connect the Filter Outlet to the Dishwasher and Faucet

  • Take the second 1/2" stainless steel flexi hose and attach one end to the outlet of the water filter.
  • Attach the other end of this hose to the existing kitchen faucet's cold-water feed connection. Ensure both connections are secure.

Step 5: Reconnect the Dishwasher Water Feed

  • Using the same 1/2" hose, connect the dishwasher back to the kitchen faucet’s cold-water feed. This ensures both the faucet and dishwasher are supplied with filtered water.

Step 6: Turn On Water and Check for Leaks

  • Slowly turn the water supply back on.
  • Check all connections for leaks, including the inlet and outlet of the filter housing, and the connections to the faucet and dishwasher.

Step 7: Flush the System

  • Run water through the kitchen faucet for a few minutes to flush out any air or particles from the filter system.


Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)